Can my screen frame be saved, or do I need a new one?

It depends on how far the aluminum has bent and whether the corners are still sound. A mild bend is usually straightened and re-squared on site. Where the frame is twisted or the corners have broken, a new frame is made to fit your opening.

Do I need a permit for screen door work in Orlando?

Like-for-like repairs such as rollers, track cleaning, rescreening, handles and locks normally require no permit in Florida. Permits are issued by your local city or county building department and apply mainly to replacing a sliding glass door unit or altering the opening. Confirm with the building department if your job grows beyond the screen.

Is pet-resistant mesh worth it?

If a dog pushes the door open with its nose or paws, standard mesh will tear again. Pet-resistant mesh is heavier and holds up better to that. Tell the technician how the door is used so the right mesh goes in.

Should I get this done before hurricane season?

It is a reasonable idea. Orlando gets wind-driven rain and gusts during the June 1 to November 30 season even this far inland, and a loose screen panel is the first thing to come out of the track. Demand in Florida rises through that same stretch.

How does the price work?

The estimate is free. The technician looks at the door, explains what the screen needs and gives you the price before any work starts, and you approve it first. You can ask for the reasoning in writing.

Screen door in Orlando, FL

If your sliding screen door has popped out, drags, or has a hole in the mesh, the cause is usually one of three things. The small rollers at the top and bottom are worn flat or seized, so the panel no longer rides the track. The light aluminum frame has bent, so one corner binds and the panel jumps out. Or the mesh itself has gone brittle and split. Often it is two of the three at once, because a panel that keeps falling out gets pushed back in by hand, and that twists the frame a little more each time.

Call now · (888) 851-3682

Phones answered around the clock · free estimate

A technician rolling new mesh into a sliding screen door frame with a spline roller on a patio table, palms and a pool in the background.

Orlando sits inland in Central Florida, so the damage here comes from humidity, sun and rain rather than salt spray. Years of UV make screen mesh brittle until it tears under a pushing dog or a knee. Constant moisture rusts small steel rollers and their bearings until they stop turning. Afternoon thunderstorms from June through September, and the wind that comes with hurricane and tropical-storm season, push on a light aluminum screen frame that was never built to take it. Add the screened lanais and pool decks on so much of Orlando's 1970s-to-2000s housing stock, where the screen door gets used many times a day, and the wear adds up fast.

While you wait — please don't

Do not force a bent frame back onto the track. A frame that is already twisted will spring back out under pressure and the corner joints break, which turns a roller job into a new frame.
Do not treat the screen as a barrier. A screen will not hold a child or a pet, and on an upstairs balcony or a second-floor unit that matters — keep the glass door closed until the screen is back on its track and latching.
Stop using the glass slider if it is also off its track. A sliding glass panel weighs as much as a person and shatters into the room if it tips, so leave it alone and have it handled by a technician.
Do not lean a loose panel against a wall or railing. A free-standing screen panel slides, falls and bends further, and the aluminum edges and broken corner keys are sharp.

What the technician does

The technician checks the rollers firstWorn, flat or seized screen rollers get replaced and the tension adjusted so the panel sits at the right height in the track. Ask to see the old roller next to the new one.
The frame is straightened or remadeA frame with a mild bend can often be straightened and re-squared. Where it is too far gone or the corners have broken, a new frame is made to the size of your opening.
The track is cleaned and checkedGrit, pollen and debris packed in the screen track grind rollers flat again within months. The track is cleared and inspected before anything is re-hung.
The panel is rescreenedTorn or brittle mesh is removed and replaced with standard mesh, or pet-resistant mesh where a dog or cat uses the door. The spline is reset so the mesh is tight and flat.
The panel goes back on and gets setThe panel is re-hung on its track with the roller tension set so it slides smoothly end to end and the latch catches without lifting or shoving.

Why this happens in Orlando, FL

Across Orlando you will find the same door in thousands of houses — the suburban subdivisions built from the 1970s through the 2000s, the newer tracts out around Lake Nona and the south and east sides, and the condos and townhomes near downtown and the tourist corridor. In Florida it is common for a home to have two or more sliders, onto a patio, a screened lanai or a pool deck, which means two or more screen panels all aging at the same rate in the same humidity and sun.

Timing matters here. Sliding door problems in Florida run year-round but peak in the summer rainy and hurricane season, and Orlando demand climbs ahead of and during that June-through-November stretch. A screen panel that is already loose in May is the one that ends up in the yard after a storm. Older downtown-adjacent neighborhoods like College Park, Lake Eola Heights and Delaney Park and newer ones like Baldwin Park and Lake Nona all see the same thing: light aluminum frames that bend, and mesh that has simply had too many years of sun.

Questions people ask

Can my screen frame be saved, or do I need a new one?: It depends on how far the aluminum has bent and whether the corners are still sound. A mild bend is usually straightened and re-squared on site. Where the frame is twisted or the corners have broken, a new frame is made to fit your opening.
Do I need a permit for screen door work in Orlando?: Like-for-like repairs such as rollers, track cleaning, rescreening, handles and locks normally require no permit in Florida. Permits are issued by your local city or county building department and apply mainly to replacing a sliding glass door unit or altering the opening. Confirm with the building department if your job grows beyond the screen.
Is pet-resistant mesh worth it?: If a dog pushes the door open with its nose or paws, standard mesh will tear again. Pet-resistant mesh is heavier and holds up better to that. Tell the technician how the door is used so the right mesh goes in.
Should I get this done before hurricane season?: It is a reasonable idea. Orlando gets wind-driven rain and gusts during the June 1 to November 30 season even this far inland, and a loose screen panel is the first thing to come out of the track. Demand in Florida rises through that same stretch.
How does the price work?: The estimate is free. The technician looks at the door, explains what the screen needs and gives you the price before any work starts, and you approve it first. You can ask for the reasoning in writing.

One call

Call (888) 851-3682 or send a request through the form, and we will arrange your screen door service in Orlando with an independent local technician — we schedule the work, we are not the contractor. The estimate is free, and you agree the price before anything is touched.

Call now · (888) 851-3682

Same problem in nearby cities

Every city we cover in Florida

Something else in this area

One Call Sliding Door Repair arranges the visit; the technician does the work and gives you the price.

Answers

Free tool

Screen mesh picker